Header photo (detail) courtesy Michael Eudenbach
Showing posts with label molds. Show all posts
Showing posts with label molds. Show all posts

Tuesday, June 7, 2011

Molds and Jigs


Workshop volunteer Paul Connors feeding the planer





Rocking the Boat participants unloading the goodies from Phily




Molds and one of the bending jigs unloaded at Rocking the Boat's
Brooklyn workshop.




A jig for bending the stem.




Jig and steambox




These two photos are of the frame bending jig. A smaller version has been built for the knees.
Notice that
next to the jig is a steambox setup. The pieces will be steamed to make them pliable before going onto the jig.


All photos courtesy Gina Pickton/Workshop on the Water

Boatbuilding glossary found at Inthe Boatshed, courtesy Gavin Atkin



Gina & Co. have been busy at the boatshop as the project heats up, with help from the CHAD group. Her report:

"We’ve been making some progress on both getting boats out of the shop, and moving forward on the whaleboat. One boat left last week and two more will be out the door next week. Then we will finally have the room freed up in the shop for the whaleboat.
On Friday we delivered some goodies to Rocking the Boat. They now have the keel pattern, the knee and frame bending jig patterns, the stem bending jig, the strongback and 8 molds. We’ve also made our own stem bending jig and are on our way to completing our own knee and frame bending jigs."

Once the strongback is set up and the molds attached, the fun should begin in earnest.

Monday, May 16, 2011

Molds completed!


One of the lofting boards in the workshop




Two mold halves about to be joined by Gina





I asked Gina how the lines on the lofting board were transferred to the pieces of wood used to build the molds. She asked if I knew of the nailhead technique. I did not, so she showed me how it works. Nails, like the ones in thi photo, are pounded in at regular intervals along the lofted line of the drawing, the the wood for the frame piece is aligned and gently impressed with the curvature of the drawing. You can see the nailhead indentations in the board.




Tools of the trade



Gina Pickton explaining some of the vagaries of the lofting/mold building process to me.




Lots of work to finish up and boats to be moved before the building of a whaleboat can take place. This will hopefully all be accomplished this week. Next a structure will be built in about the area occupied by the blue lift to attach and stabilize the boat skeleton, the molds, keel, stem and sternpost on a 'strongback' or table/platform as these boats are built upright, Norwegian style and not upside down which is the more common practice.


All Photos courtesy Snez'a Litinovic





Last Sunday, (meaning March 8) I met a new friend for the first time. We'd been conversing by email and since she lives in Philadelphia I thought we could combine a visit to the Independence seaport museum with a visit to the workshop to update the progress on the whaleboats. Snez'a had never seen the museum and we had a lot of fun viewing and discussing the collection. Snez'a is an architect (her firm, 119 Degrees Architects) so a lot of what she was seeing in terms of process and drawings and form made sense to her, and led to lively discussion. I had left my camera behind but fortunately Snez'a had a little battery time left on her camera and was able to get some photos. Gina Pickton was finishing up the mold building for the whaleboat project and was very gracious in showing us how the process worked and answering our questions.




Molds finished and stored awaiting the building of support structure and strongback




Same with these, one set for Philly and one for NYC




One half of the frame building jig being built by the school team from CHAD school in Philadelphia



ditto


photos courtesy Gina Pickton





Gina finished up the molds for both boats this week and was kind enough to send some photos along with a brief update on the progress.

"This week we finished up both sets of molds. Now we’re taking a moment to finish up the Elco’s Tranquility and Bear Cub, and the Marsh Cat to clear space before we continue on.
The pictures above are of both sets of Whaleboat molds ( for this workshop and the one in NYC at Rocking the boat, ed.), stored out of the way until needed

On Wed we have some regular kids from the CHAD school here in Philadelphia. They are working on jigs for the whaleboat.The lobster trap looking thing is the frame bending jig the kids are working on. We’ll get pictures of them working on it next week."


Once the project is properly underway, Gina will be sending me regular updates and I will attempt to visit as often as possible as well to document the build in Philadelphia, with project director Geoff McKonley updating me from NY.
Stay tuned.

Saturday, April 30, 2011

Building Molds for the Whaleboats Project


Here we see molds 1 and 2 labeled RtB




Gina here is joining a two piece half mold




and here




Mold # 1 for the ISM boat. These are long and narrow boats. 28' feet long and as Gina measured from the lofting board today, just under 6' beam. They are quick, maneuverable and responsive, and will have gaff rigs.




Mold parts awaiting assembly




More of that (those)




And yet more




Gina Pickton assembling parts into a complete mold




Laying them down onto the lofted lines to check for accuracy




putting it together




You can't really see it, but Gina has in hand a small template for drawing, then cutting, a keel rabbet before joining the mold halves




Keel rabbet




This is a model whaleboat from the museums collection, dusted off and installed in the visitors
section of the workshop so folks can see what the finished boats will look like. Gina says this little exhibit has been very successful.





Amistad, Gina worked aboard Amistad in 2007

courtesy Gina Pickton





Crewing aboard Gazela

courtesy Gina Pickton






Replanking schooner Dolphin

courtesy Gina Pickton



All photos Thomas Armstrong, unless otherwise attributed




Willets Ansel, author of The Whaleboat, defines molds as: 'Temporary forms used in whaleboat construction , around which the boat is planked'. Apparently the term is so ubiquitous I found no other definition in about two hours of searching the internet and boatbuilding texts including Chapelle. So let me attempt to expand on Willets' definition. Molds are built to conform to the inside form of a boat drawing, taken in regular vertical sections and serve as a framework around which the actual boat is built. Most common practice today in traditional construction of small boats have the molds set upside down and the boat is only turned right side up after planking is finished. The whaleboats are built right side up, like Norwegian small boats and most larger boats and ships.
The lines of a boat are drawn full size and laid down on a lofting board. The molds are cut to conform to these lines. Once built, the molds are secured to a 'strongback' or support frame or 'table' to allow the building of the boat.

I visited the boatshop today to see what progress had been made on the building of the molds for the two whaleboats. I found Gina Pickton, an employee of the workshop, busy putting together precut peices of the molds. The mold halves are joined after cutting rabbets for the keel to fit into. After they are joined more rabbets will be cut for battens or ribbands, horizontal strips running the length of the boat to tie the molds together. With molds and ribbands in place and the keel laid, all is secured to the strongback and planking can commence. These boats are unusual as the garboard, (gar·board/ˈgärˌbôrd/
Noun: The first range of planks or plates laid on a ship's bottom next to the keel.) and the next strake (1st strake) and the top two strakes (gunwale and sheer strake) are built lapstrake, while all other planking is carvel.
Gina and co. are building two sets of molds, one for the ISM boat and one for Rocking the Boat in NY.
When I visited, Gina was quite accommodating, answering my questions and allowing me to document her work. She also showed me a portion of a 6 hour (3)DVD set from Mystic Seaport which follows the construction of a whaleboat there. The team at WoW are using this as a guide to sequence their build and to answer many of the questions that come up along the way.

A quick note about Gina Pickton. She has been an employee of the boatshop for about 1.5 yrs. and has been involved with boats for over a decade, mostly larger boats, tall ships. All the work she has done prior to the whaleboat project has been repair/reconstruction maintenance type work. She allowed that she is very excited to participate in a ground up new build project.

Monday, April 25, 2011

Molds

Whaleboat molds were cut from the lofted plan last week. Two sets were made; one to send up to Rocking the Boat in NYC. The students there will be building a boat with Geoff Mc. while his cohort Tony A. is rowing another one of the boats built by the students to Maine and back as a fund raiser for the program.

The other set of molds will be erected at the Workshop on the Water. They will form the shape of things to come. Really they will shape the form of the whaleboat.

We will be following up soon with more on the molds and their setup, hopefully, watch this space. (ed)